BIOPAC® Systems, Inc. Logo

Universal Interface Module

Life Science Data Acquisition at its Best

record data

Request More Info
Universal Interface Module
Part #: UIM100C

The UIM100C is used to connect 100-series amplifier modules and signal cables to an MP system and was included in older MP150 and MP100 Starter Systems.

Note: The current MP160 Research System includes an HLT100C for connecting 100C-series amplifier modules and signal cables. UIM100C is not supplied or required with the MP160.

Sixteen analog input channels plus 2 analog output channels are provided via standard 3.5 mm phone jacks on the front panel. The back panel provides access to 16 digital I/O lines and an external trigger input via screw terminals. Amplifier modules snap onto the side of the UIM100C for signal routing to the MP50 or MP100 data acquisition unit. The output of any amplifier module snapped to the UIM100C can be monitored, during acquisition, via the corresponding 3.5 mm analog channel phone jack.

The UIM100C also provides a direct link to the analog and digital I/O lines of the MP device when collecting or sending data to external equipment.

See More...

UIM100C Universal Interface Module
View Spec PDF

Are You Looking for These?

Part #: UIM100C
Categories: Amplifiers - Research
Subcategories: Interface Modules - Research

Details

Compatibility


Connecting the UIM100C to older MP Systems
  • MP150: Snap the UIM100C onto the right side of the MP150.
  • MP100: Connect the UIM100C to the MP100 acquisition unit via two included 0.6-meter cables:
    o 37-pin connector for analog signals
    o 25-pin connector for digital signals

When using the Universal Interface Module (UIM100C) with other 100-Series modules, the UIM100C is usually the first module cascaded in the chain. If using the STM100C, OXY100C or HLT100C, the module must be plugged in on the left of the UIM100C. Up to seventeen modules (including the UIM100C) can be snapped together.

See Cables & Accessories for cables to interface your equipment to the UIM100C.

IMPORTANT USAGE NOTE

Mains powered external laboratory equipment should not be connected to an MP150 or MP100 System (via the UIM100C), when the system also connects to electrodes attached to humans. For analog signals, use the INISO or OUTISO (using the HLT100C) to couple external equipment to an MP System. For digital signals, use the STP100 (using the UIM100C) to couple external equipment to an MP150 or MP100 System. Contact BIOPAC for details.

Support

Downloads/Resources

Knowledge Base

Recommended Items

Spotlight On
continuous NIR spectroscopy (NIRS) module

fNIR Imaging Systems

fNIR Imaging Systems are stand-alone functional brain imaging solutions for continuous NIR spectroscopy (NIRS). They provide an in-lab cognitive function assessment and eliminate a great many of the drawbacks of a functional MRI. fNIR optical imaging technology measures neural activity and hemodynamic response in the prefrontal cortex. Subjects wear an fNIR sensor (IR light sources […]

View All
Latest News

NEWS CITATIONS – Heart Rate & Heart Rate Variability, Wingate Anaerobic Test, and Neuroscience of Music

BIOPAC provides software and hardware that allow for research teams to record and analyze respiration activity in physiological experimentation. Here are a few notable studies covering HRV, EMG, and EEG measurement. HRV (Jing Wei, Hong Luo, Si J. Wu, Paul P. Zheng, Genyue Fu, and Kang Lee) Humans encounter various stressful situations everyday at work, home, and school. Such stress when experienced at high degrees and/or […]

What makes you laugh the most?

Alan Macy Answers Proust Questionnaire BIOPAC co-founder and R&D Director, Alan Macy, was interviewed recently by Roger Durling for the Santa Barbara Independent. The article, “The S.B. Questionnaire: Alan Macy,” provided a background excerpt of the Santa Barbara entrepreneurs’ past as well as his answers to the Proust Questionnaire. The biomedical technology developed at BIOPAC reflects an ambitious […]

Read All
Request a Demonstration
Request a Demonstration