BIOPAC® Systems, Inc. Logo

Electrobioimpedance Smart Amplifier

Request More Info
Smart Amp Bioimpedance
Part #: EBI100D

The Electrobioimpedance (EBI) Smart Amplifier is specifically designed to measure thoracic impedance for performing various impedance signals and may be used for any body impedance measurement, including respiration and cardiac output. The electrical bioimpedance amplifier terminates in two connectors for Magnitude of impedance (MAG) and Phase of Impedance (PHS), with Derived dZ/dt available as an optional calculation channel (enable “Show inverted ICG”); channel scaling can be employed to specify the dZ/dt polarity. Use with EL500 series disposable electrodes and LEAD131 for a four-spot electrode configuration or LEAD132 for an eight-spot electrode configuration; contact BIOPAC for use with ICG tape. Amplifier has a 3 m cable that connects directly to an AMI100D Amplifier Input Module.

BIOPAC’s new Smart Amplifiers are designed for great data. Smart Amplifiers improve performance by amplifying the physiological signal close to the subject, which allows a high-level voltage connection to the data acquisition system and reduces noise artifact.

AcqKnowledge Smart Amp setup includes guides and prompts to prevent errors. Plus, channels are automatically set to be plotted and included in input values display, with the initial visual range set to the min/max input range for that Smart Amplifier signal type, in appropriate units.

The Smart Amplifier may be attached to the subject either using the included Velcro backed clip or optional Velcro straps around the subject.

See More...

Impedance Amp
View Spec PDF

Are You Looking for These?

Part #: EBI100D
Categories: Smart Amplifiers - Research, Amplifiers - Research
Subcategories: Transducer Amplifiers - Research

Alternatives
For the same Platform

Equivalents
With a different Platform

Details

Compatibility


Reduced wiring in Smart Amp setups reduces ambient and common mode noise, increases comfort, and improves the group dynamic!

Smart Amplifiers connect to an MP160 Research System via an Amplifier Interface Module (AMI100D); Smart Amps are not compatible with MP150, MP100, HLT100C, or MP36R devices. For output, add CBL237 with OUTISO or similar. AcqKnowledge Smart Amp setup includes guides and prompts to prevent errors. Plus, channels are automatically set to be plotted and included in input values display, with the initial visual range set to the min/max input range for the Smart Amplifier signal type, in appropriate units. AcqKnowledge 5.0.4 and above support Smart Amp functionality.

AcqKnowledge Smart Amp setupAuto-detect signal type & offer derived measures

Green: configured & detected

Red: configured but not found

White: available

Dashed: unavailable—in use by another analog input

For quick access to Smart Amp options, click the CH# box.

 

 

The Smart Amplifier ships with the following accessories:

  • Protective zippered case with accessory pockets
  • Clip for attaching Smart Amplifier to clothing or other materials on the subject
  • One bag of silicone cable ID tags which may be written specific signal type or identifier on and attached to both ends of the cable for easy identification
  • One silicone cable wrap to optionally allow for unused lengths of cable to be wrapped around to shorten overall cable length
  • One cable management clip that may be optionally attached to the cable to route it around the subject

Possible Lead Configurations

Electrical bioimpedance setups for absolute or relative measurement

Suggested Reading

Methodological Guidelines for Impedance Cardiography , PSYCHOPHYSIOLOGY, Vol. 27, No. 1

See more on the Support tab > Downloads & Resources.

Videos

Integrating BIOPAC Research Systems | Data Acquisition & Analysis

Automated ECG Analysis- Lead II

BIOPAC Research Solutions | ECG

Classify Heartbeats

EL-CHECK Electrode Impedance Checker

Marking and Interpolating Segments

Support

Downloads/Resources

Knowledge Base

Recommended Items

Spotlight On
BIOPAC Evoked Response Module

ERS Smart Amplifier

The ERS Evoked Response Smart Amplifier is an extremely low noise differential amplifier that accurately amplifies very small potentials, such as those associated with stimulus/response, startle response, ABR auditory brainstem response, somatosensory evoked response, signal-averaged recordings, and nerve conduction velocity recordings. BIOPAC’s new Smart Amplifiers are designed for great data. Smart Amplifiers improve performance by […]

View All
Latest News

New Citations | BIOPAC in Psychophysiology Research

The mind and body work together in many ways and psychophysiology research provides insight to these connections. BIOPAC has a variety of systems to power your emotion, arousal, stress, cognitive assessment, group interaction, startle, and other psychophysiology research. Here are some recent studies that have used BIOPAC systems for psychophysiological research… Skin conductance, facial EMG, […]

Seenel Imaging and BIOPAC Systems, Inc. Announce a Global Partnership

           For immediate release: January 4, 2023 Amiens, France and GOLETA, California, USA Seenel Imaging SAS and BIOPAC Systems, Inc. have formed a long-term global partnership to distribute MedelOpt®, Seenel Imaging’s groundbreaking wearable neuroimaging device for the neuroscience research market. Seenel Imaging, based in France, continues its international expansion by partnering with BIOPAC Systems, […]

Read All
Request a Demonstration
Request a Demonstration