BIOPAC® Systems, Inc. Logo

Galvanic Oxygen Sensor 0-100%

Request More Info
Oxygen Sensor
Part #: RX301

The RX301 sensor has a response time of approximately 12 seconds for measuring changes in oxygen levels for air flow rates of 0.2-2 L/min with approximately 2% linearity.

The sensor incorporates a threaded neck to allow mounting in a housing or pipe wall to sense oxygen concentrations in a sealed chamber or directed flow stream.

The expected lifetime of the RX301 sensor is approximately five years in constant exposure to atmosphere. To maximize the sensor’s longevity, keep it sealed in an airtight container away from direct sunlight, preferably at a temperature between 10 and 22 ºC, when not in use.

The RX301 sensor attaches to the TSD301 Galvanic Oxygen Transducer.

See More...

BIOPAC O2 sensor
View Spec PDF

Are You Looking for These?

Part #: RX301

Subcategories: Accessories - , Gas Analysis -

Details

Compatibility


Operating Principle: Electrochemical (Galvanic)
Range: 0-100% Oxygen Concentration
Output: 8.0-12.0 mV nominal (dry air at 25 °C)
Response Time (10% to 90%): Less than 12 seconds @ flow range 0.2-2.0 Liters/min
Operating Temperature: 0 to 45 °C
Linearity: ±2% of Full Scale Range, applied for 5 minutes
Stability: Less than 1% of Full Scale Range, 8 hour period, constant Temperature, Pressure, Humidity
Humidity: 5%-95% Relative, Non-condensing
Temperature Compensation: NTC (internal)
Warm-up Time: Less than 30 minutes, after sensor replacement
Calibration: Sensor is typically calibrated from 20.93% oxygen in ambient “fresh” air to 100% oxygen from a tank source.
Expected Life: Greater than 1,000,000 oxygen hours (approximately five and a half years in ambient air)
Zero Offset: Less that 200 µV (100% Nitrogen – 5 minutes)
Storage Temperature Range: -20 to 50 °C (recommended 5 to 30 °C)
Electrical Connector: 3.5 mm female mono phone jack
Sensing port threads: Tap size is M16-1 (15 mm drill hole)
Interface: TSD301 transducer cabling to DA100C transducer amp
Cable length: 3 meters (on TSD301)
Load Resistance: 10 kohms (TSD301 assy)

Support

Downloads/Resources

Knowledge Base

Recommended Items

Spotlight On
Smart Center controller, 2-3 wireless transmitters & AcqKnowledge plus case

Smart Center | Stand-alone BioNomadix Wireless Systems

Smart Center Stand-alone, Portable Wireless Physiology Systems Smart Center Essentials entry-level system includes a Smart Center Device (BN-SMART with USB power cable), 2 or 3 Transmitters (BN-xxx-T with chargers); AcqKnowledge for Smart Center, and a case. Smart Center Enhanced adds a Logger (BN-LOGGER) and Basic Scripting License (ACK100W-BAS) to the Smart Center Device (BN-SMART with powercable), 3 […]

View All
Latest News

New Citations | Marking Events with BIOPAC

BIOPAC offers complete systems for life science research and education—human, animal, or in vivo studies, as well as powerful software and automated analysis including industry-standard data acquisition amplifiers, transducers & electrodes. BIOPAC can be used inside or outside the lab to measure physiology anytime, anyplace. Impact of Movie Editing on Perceptual Conflict Mechanisms Our ability to watch and understand films effortlessly […]

Electrocardiography Guide Now Available

BIOPAC’s comprehensive Introductory ECG Guide addresses fundamental to advanced concerns to optimize electrocardiography data recording and analysis. Topics include: ECG Complex; Electrical and Mechanical Sequence of a Heartbeat; Systole and Diastole; Configurations for Lead I, Lead II, Lead III, 6-lead ECG, 12-lead ECG, precordial leads; Ventricular Late Potentials (VLPs); ECG Measurement Tools; Automated Analysis Routines for extracting, […]

Read All
Request a Demonstration
Request a Demonstration