BIOPAC® Systems, Inc. Logo

Galvanic Oxygen Transducer 0-100%

Request More Info
View Cart “Galvanic Oxygen Sensor 0-100%” has been added to your cart.
Galvanic Oxygen Transducer
Part #: TSD301

The TSD301 Galvanic Oxygen Transducer is used to measure ambient or flow stream oxygen levels in a range of 0-100%. The TSD301 has a response time of approximately 12 seconds for measuring changes in oxygen levels for input gases at a flow rate of 0.2-2.0 L/min with approximately 2% linearity.

The TSD301 transducer incorporates a detachable sensor (RX301). The sensor operates via the electrochemical (galvanic) principle and is replaceable; the sensor has an expected lifetime of approximately five years in constant exposure to atmosphere.

Interfaces with DA100C.

See More...

BIOPAC O2 measurement
View Spec PDF

Are You Looking for These?

Part #: TSD301
Categories: Amplifiers - Research
Subcategories: Gas Analysis - Research

Details

Compatibility


Operating Principle: Electrochemical (Galvanic)
Range: 0-100% Oxygen Concentration
Output: 8.0-12.0 mV nominal (dry air at 25 °C)
Response Time (10% to 90%): Less than 12 seconds @ flow range 0.2-2.0 Liters/min
Operating Temperature: 0 to 45 °C
Linearity: ±2% of Full Scale Range, applied for 5 minutes
Stability: Less than 1% of Full Scale Range, 8 hour period, constant Temperature, Pressure, Humidity
Humidity: 5%-95% Relative, Non-condensing
Temperature Compensation: NTC (internal)
Zero Offset: Less that 200 µV (100% Nitrogen–5 minutes)
Warm-up Time: Less than 30 minutes, after sensor replacement
Calibration: Sensor is typically calibrated from 20.93% oxygen in ambient “fresh” air to 100% oxygen from a tank source.
Expected Life: Greater than 1,000,000 oxygen hours (approximately five and a half years in ambient air)
Storage Temperature Range: -20 to 50 °C (recommended 5 to 30 °C)
Electrical Connector: 3.5 mm female mono phone jack
Sensing port threads on RX301: Tap size is M16-1 (15 mm drill hole)
Interface: DA100C, via TSD301 cabling
Cable length: 3 meters (TSD301)
Load Resistance: 10 kohms (TSD301 assy)
Replacement Sensor: RX301 (detachable from TSD301)

Support

Downloads/Resources

Knowledge Base

Recommended Items

Spotlight On

EDA Electrodermal Activity Amplifier for MRI

MRI Smart Amplifier The EDA100C-MRI measures both the skin conductance level (SCL) and skin conductance response (SCR) as they vary with sweat gland (eccrine) activity due to stress, arousal or emotional excitement. The EDA100C-MRI uses a constant voltage (0.5 V) technique to measure skin conductance. The controls allow selection of absolute (SCL+SCR) or relative (SCR) […]

View All
Latest News

New Citations | BIOPAC in EDA Research

Researchers utilize electrodermal activity (EDA) data in a wide array of protocols. These recent studies join thousands of BIOPAC citations for EDA and represent just a few of BIOPAC’s hardware options for wired, wireless, logged, or MRI protocols with reusable or disposable EDA accessories and AcqKnowledge software solutions for Automated EDA Analysis Routines and EDA Measurement Tools. Caffeine Delivery […]

EDA Guide Available

BIOPAC’s comprehensive EDA Guide provides an introduction to Electrodermal Activity (EDA or GSR) and details topics including: EDA Complex: SCL, SCR, tonic, phasic, specific SCR, non-specific SCR Participant Prep & Electrode Placement Data Recording tips Automated EDA Analysis Routines Digital input to Stim Events Stim-Response Analysis Derive Phasic EDA from Tonic Event-related EDA Analysis Locate […]

Read All
Request a Demonstration
Request a Demonstration